Name

mount.cifs — mount using the Common Internet File System (CIFS)

Synopsis

mount.cifs {service} {mount-point} [-o options]

DESCRIPTION

This tool is part of the Samba(7) suite.

mount.cifs mounts a Linux CIFS filesystem. It is usually invoked indirectly by the mount(8) command when using the "-t cifs" option. This command only works in Linux, and the kernel must support the cifs filesystem. The CIFS protocol is the successor to the SMB protocol and is supported by most Windows servers and many other commercial servers and Network Attached Storage appliances as well as by the popular Open Source server Samba.

The mount.cifs utility attaches the UNC name (exported network resource) to the local directory mount-point. It is possible to set the mode for mount.cifs to setuid root to allow non-root users to mount shares to directories for which they have write permission.

Options to mount.cifs are specified as a comma-separated list of key=value pairs. It is possible to send options other than those listed here, assuming that cifs supports them. If you get mount failures, check your kernel log for errors on unknown options.

mount.cifs is a daemon. After mounting it keeps running until the mounted resource is unmounted (usually via the umount utility)

OPTIONS

username=arg

specifies the username to connect as. If this is not given, then the environment variable USER is used. This option can also take the form "user%password" or "user/workgroup" or "user/workgroup%password" to allow the password and workgroup to be specified as part of the username.

password=arg

specifies the CIFS password. If this option is not given then the environment variable PASSWD is used. If it can find no password mount.cifs will prompt for a passeword, unless the guest option is given.

Note that password which contain the arguement delimiter character (i.e. a comma ',') will failed to be parsed correctly on the command line. However, the same password defined in the PASSWD environment variable or a credentials file (see below) will be read correctly.

credentials=filename

specifies a file that contains a username and/or password. The format of the file is:

.nf
		username = value
		password = value
.fi

This is preferred over having passwords in plaintext in a shared file, such as /etc/fstab. Be sure to protect any credentials file properly.

uid=arg

sets the uid that will own all files on the mounted filesystem. It may be specified as either a username or a numeric uid. This parameter is ignored when the target server supports the CIFS Unix extensions.

gid=arg

sets the gid that will own all files on the mounted filesystem. It may be specified as either a groupname or a numeric gid. This parameter is ignored when the target server supports the CIFS Unix extensions.

port=arg

sets the port number on the server to attempt to contact to negotiate CIFS support. If the CIFS server is not listening on this port or if it is not specified, the default ports will be tried i.e. port 445 is tried and if no response then port 139 is tried.

file_mode=arg

If the server does not support the CIFS Unix extensions this overrides default file mode which will be used locally.

dir_mode=arg

If the server does not support the CIFS Unix extensions this overrides the default mode for directories.

ip=arg

sets the destination host or IP address.

domain=arg

sets the domain (workgroup) of the user

guest

don't prompt for a password

ro

mount read-only

rw

mount read-write

rsize

default network read size

wsize

default network write size

ENVIRONMENT VARIABLES

The variable USER may contain the username of the person using the client. This information is used only if the protocol level is high enough to support session-level passwords. The variable can be used to set both username and password by using the format username%password.

The variable PASSWD may contain the password of the person using the client. This information is used only if the protocol level is high enough to support session-level passwords.

The variable PASSWD_FILE may contain the pathname of a file to read the password from. A single line of input is read and used as the password.

NOTES

This command may be used only by root.

CONFIGURATION

The primary mechanism for making configuration changes and for reading debug information for the cifs vfs is via the Linux /proc filesystem. In the directory /proc/fs/cifs are various configuration files and pseudo files which can display debug information. For more information see the kernel file fs/cifs/README

BUGS

Passwords and other options containing , can not be handled. For passwords an alternative way of passing them is in a credentials file or in the PASSWD environment.

The credentials file does not handle usernames or passwords with leading space.

Note that the typical response to a bug report is suggestion to try the latest version first. So please try doing that first, and always include which versions you use of relevant software when reporting bugs (minimum: samba, kernel, distribution)

VERSION

This man page is correct for version 3.0 of the Samba suite.

SEE ALSO

Documentation/filesystems/cifs.txt and fs/cifs/README in the linux kernel source tree may contain additional options and information.

AUTHOR

Steve French

The syntax and manpage were loosely based on that of smbmount. It was converted to Docbook/XML by Jelmer Vernooij.

The current maintainer of the Linux cifs vfs and the userspace tool mount.cifs is Steve French. The SAMBA Mailing list is the preferred place to ask questions regarding these programs.