Statistics
==========
Dovecot v2.1+ supports gathering/reporting mail (IMAP, POP3, LDA, LMTP, etc.)
statistics. There are different "zoom levels" you can look at the statistics:
* command: Per-IMAP command
* session: Per IMAP/POP3 connection
* user: Per user (all of user's sessions summed up)
* domain: Per domain (all of domain's users summed up)
* ip: Per IP address (all sessions from the IP summed up)
Basic Configuration
-------------------
---%<-------------------------------------------------------------------------
mail_plugins = $mail_plugins stats
protocol imap {
mail_plugins = $mail_plugins imap_stats
}
plugin {
# how often to session statistics
stats_refresh = 30 secs
# track per-IMAP command statistics
stats_track_cmds = yes
}
---%<-------------------------------------------------------------------------
You'll also need to give enough permissions for mail processes to be able to
write to stats-mail fifo. For example if you use a single "vmail" user for mail
access:
---%<-------------------------------------------------------------------------
service stats {
fifo_listener stats-mail {
user = vmail
mode = 0600
}
}
---%<-------------------------------------------------------------------------
Memory usage configuration
--------------------------
The stats process attempts to keep memory usage below a specified amount. This
value is only approximate because of extra overhead caused by malloc() itself.
---%<-------------------------------------------------------------------------
stats_memory_limit = 16 M
---%<-------------------------------------------------------------------------
Once the memory limit is reached, oldest statistics are freed from memory.
Different statistics levels have different timeout limits, which are configured
in:
---%<-------------------------------------------------------------------------
stats_command_min_time = 1 mins
stats_domain_min_time = 12 hours
stats_ip_min_time = 12 hours
stats_session_min_time = 15 mins
stats_user_min_time = 1 hours
---%<-------------------------------------------------------------------------
So for example the above means:
* An IMAP command is kept in memory for at least 1 minute after it has
finished
* A user is kept in memory for 1 hour after its last session has disconnected.
The stats process attempts to honor these min_time-settings, but if memory is
tight it can go below these values to honor the 'stats_memory_limit' setting.
Statistics gathered
-------------------
Statistics gathered using the 'getrusage()' system call:
* user_cpu: User CPU (seconds.microseconds)
* sys_cpu: System CPU (seconds.microseconds)
* min_faults: Minor page faults (page reclaims)
* maj_faults: Major page faults
* vol_cs: Voluntary context switches
* invol_cs: Involuntary context switches
* disk_input: Number of bytes read from disk
* disk_output: Number of bytes written to disk
The disk_input and disk_output attempt to count the actual read/write bytes to
physical disk, so e.g. reads from OS's cache aren't counted. Note that not all
operating systems and filesystem support this, instead they simply show these
values always as 0.
Statistics gathered from '/proc/self/io' output (Linux-only):
* read_count: Number of read() syscalls
* write_count: Number of write() syscalls
* read_bytes: Number of bytes read using read() syscalls
* write_bytes: Number of bytes written using write() syscalls
Note that the above numbers are not only about disk I/O, but also about network
I/O, Dovecot's IPC and every other kind of reads/writes as well.
Statistics gathered by Dovecot's lib-storage internally:
* mail_lookup_path: Number of open() and stat() calls (i.e. "path lookups")
* mail_lookup_attr: Number of stat() and fstat() calls
* mail_read_count: Number of read() calls for message data (e.g. index files
not counted)
* mail_read_bytes: Number of message bytes read()
* mail_cache_hits: Number of cache hits from 'dovecot.index.cache' file
doveadm stats
-------------
top
---
'doveadm stats top [<sort field>]'
The top command gives a very simple "top"-like view of connected sessions. The
optional sort field is one of:
* disk: disk_input and disk_output summed up (default)
* cpu: user_cpu and sys_cpu summed up
* any other statistics field
dump
----
'doveadm stats dump <level> [<filter>]'
The dump command shows a raw output of the statistics. The level parameter is
one of the levels listed at the top of this page (e.g. "session"). The filter
can contain zero of more filters:
* connected: The session must be currently connected (or the user/domain/ip
must have at least one session that is currently connected)
* since=<timestamp>: Last update was since this UNIX timestamp
* user=<wildcard>: Username matches this wildard
* domain=<wildcard>: Domain name matches this wildard
* ip=<ip>[/bits]: IP address matches this IP/network (e.g. 192.168.1.0/24)
If nothing matches the filter, the output is a single empty line. Otherwise it
begins with a header line followed by data lines. Each line has a list of
fields separated by TABs. The header describes what the data fields are. The
list of fields depends on what level you're listing. Some of the fields are:
* session: 128 bit session GUID in hex format. This uniquely identifies a
single session. Used by commands and sessions.
* connected: Is the client currently connected? 0=no, 1=yes.
* pid: Process ID of the session. If the session is no longer connected, the
PID may not exist anymore.
* last_update: UNIX timestamp of the last time this data was updated
* reset_timestamp: UNIX timestamp of when this user/domain/ip structure was
created. This is useful when you want to track incrementally what changed:
* If timestamp is the same as in your previous lookup, you can simply count
different = new_value - previous_value.
* If timestamp has changed since your previous lookup, the statistics were
reset to zero since and the difference = new_value.
Stats protocol
--------------
You can connect to stats process via '$base_dir/stats' UNIX socket, or you can
simply add more UNIX/TCP listeners to the stats service, e.g.:
---%<-------------------------------------------------------------------------
service stats {
inet_listener {
listen = 127.0.0.1
port = 24242
}
}
---%<-------------------------------------------------------------------------
The protocol is almost entirely identical to 'doveadm stats dump' command's
parameters and output. The only difference is that you prefix your request with
"EXPORT<tab>". For example:
---%<-------------------------------------------------------------------------
EXPORT<tab>session<tab>connected<lf>
---%<-------------------------------------------------------------------------
The output will be identical to 'doveadm stats dump session connected' command.
(This file was created from the wiki on 2011-11-16 14:09)