# $OpenLDAP$
# Copyright 1999-2011 The OpenLDAP Foundation, All Rights Reserved.
# COPYING RESTRICTIONS APPLY, see COPYRIGHT.
H1: Running slapd
{{slapd}}(8) is designed to be run as a standalone service. This
allows the server to take advantage of caching, manage concurrency
issues with underlying databases, and conserve system resources.
Running from {{inetd}}(8) is {{NOT}} an option.
H2: Command-Line Options
{{slapd}}(8) supports a number of command-line options as detailed
in the manual page. This section details a few commonly used options.
> -f <filename>
This option specifies an alternate configuration file for slapd.
The default is normally {{F:/usr/local/etc/openldap/slapd.conf}}.
> -F <slapd-config-directory>
Specifies the slapd configuration directory. The default is {{F:/usr/local/etc/openldap/slapd.d}}.
If both {{EX:-f}} and {{EX:-F}} are specified, the config file will be read and converted
to config directory format and written to the specified directory.
If neither option is specified, slapd will attempt to read the default config
directory before trying to use the default config file. If a valid config
directory exists then the default config file is ignored. All of the slap tools
that use the config options observe this same behavior.
> -h <URLs>
This option specifies alternative listener configurations. The
default is {{EX:ldap:///}} which implies {{TERM:LDAP}} over
{{TERM:TCP}} on all interfaces on the default LDAP port 389. You
can specify specific host-port pairs or other protocol schemes (such
as {{EX:ldaps://}} or {{EX:ldapi://}}).
!block table
URL Protocol Transport
ldap:/// LDAP TCP port 389
ldaps:/// LDAP over SSL TCP port 636
ldapi:/// LDAP IPC (Unix-domain socket)
!endblock
For example, {{EX:-h
"ldaps:// ldap://127.0.0.1:666"}} will create two listeners: one
for the (non-standard) {{EX:ldaps://}} scheme on all interfaces on
the default {{EX:ldaps://}} port 636, and one for the standard
{{EX:ldap://}} scheme on the {{EX:localhost}} ({{loopback}}) interface
on port 666. Hosts may be specified using using hostnames or
{{TERM:IPv4}} or {{TERM:IPv6}} addresses. Port values must be
numeric.
For LDAP over IPC, the pathname of the Unix-domain socket can be encoded
in the URL. Note that directory separators must be
URL-encoded, like any other characters that are special to URLs.
Thus the socket {{EX:/usr/local/var/ldapi}} must be encoded as
> ldapi://%2Fusr%2Flocal%2Fvar%2Fldapi
ldapi: is described in detail in {{Using LDAP Over IPC Mechanisms}} [{{REF:Chu-LDAPI}}]
Note that the ldapi:/// transport is not widely implemented: non-OpenLDAP clients
may not be able to use it.
> -n <service-name>
This option specifies the service name used for logging and
other purposes. The default service name is {{EX:slapd}}.
> -l <syslog-local-user>
This option specifies the local user for the {{syslog}}(8)
facility. Values can be {{EX:LOCAL0}}, {{EX:LOCAL1}}, {{EX:LOCAL2}}, ...,
and {{EX:LOCAL7}}. The default is {{EX:LOCAL4}}. This option
may not be supported on all systems.
> -u user -g group
These options specify the user and group, respectively, to run
as. {{EX:user}} can be either a user name or uid. {{EX:group}}
can be either a group name or gid.
> -r directory
This option specifies a run-time directory. slapd will
{{chroot}}(2) to this directory after opening listeners but
before reading any configuration files or initializing
any backends.
.
> -d <level> | ?
This option sets the slapd debug level to <level>. When level is a
`?' character, the various debugging levels are printed and slapd
exits, regardless of any other options you give it. Current
debugging levels are
!block table; colaligns="RL"; align=Center; \
title="Table 7.1: Debugging Levels"
Level Keyword Description
-1 any enable all debugging
0 no debugging
1 (0x1 trace) trace function calls
2 (0x2 packets) debug packet handling
4 (0x4 args) heavy trace debugging
8 (0x8 conns) connection management
16 (0x10 BER) print out packets sent and received
32 (0x20 filter) search filter processing
64 (0x40 config) configuration processing
128 (0x80 ACL) access control list processing
256 (0x100 stats) stats log connections/operations/results
512 (0x200 stats2) stats log entries sent
1024 (0x400 shell) print communication with shell backends
2048 (0x800 parse) print entry parsing debugging
16384 (0x4000 sync) syncrepl consumer processing
32768 (0x8000 none) only messages that get logged whatever log level is set
!endblock
You may enable multiple levels by specifying the debug option once for each desired level. Or, since debugging levels are additive, you can do the math yourself. That is, if you want to trace function calls and watch the config file being processed, you could set level to the sum of those two levels (in this case, {{EX: -d 65}}). Or, you can let slapd do the math, (e.g. {{EX: -d 1 -d 64}}). Consult {{F: <ldap_log.h>}} for more details.
Note: slapd must have been compiled with {{EX:--enable-debug}}
defined for any debugging information beyond the two stats levels
to be available (the default).
H2: Starting slapd
In general, slapd is run like this:
> /usr/local/libexec/slapd [<option>]*
where {{F:/usr/local/libexec}} is determined by {{EX:configure}}
and <option> is one of the options described above (or in {{slapd}}(8)).
Unless you have specified a debugging level (including level {{EX:0}}),
slapd will automatically fork and detach itself from its controlling
terminal and run in the background.
H2: Stopping slapd
To kill off {{slapd}}(8) safely, you should give a command like this
> kill -INT `cat /usr/local/var/slapd.pid`
where {{F:/usr/local/var}} is determined by {{EX:configure}}.
Killing slapd by a more drastic method may cause information loss or
database corruption.